چسب دوقلو (اپوکسی) متال BISON هلند

چسب دوقلو (اپوکسی) متال BISON هلند

- چسب دوقلو (اپوکسی) متال خاصیت پرکنندگی بسیار بالا برای فلزات و ترک خوردگی ها

- تحمل فشار بعداز خشک شدن 180 کیلوگرم بر سانتی متر مربع

- تحمل حرارت تا 100+ درجه سانتی گراد

- زمان خشک شدن 10ساعت بعد از ترکیب و گیرایش نهایی بعد از 24 ساعت

 ___________________________________________________________

• Extreme strength: up to 220 kg/cm²
• Metal coloured
• Resistant to harsh conditions
• Resistant to temperatures between -40°C and +100°C
• Filling
• (Sea)water resistant
• Very good chemical resistance
• Can be sanded, filed, drilled and painted after curing

Working Conditions: Only apply at temperatures between +5°C and +35°C. Product cures by mixing the resin and hardener.
Safety: Preferably wear gloves.
Preliminary treatment: Degrease parts to be bonded with acetone. Roughen smooth surfaces (sandpaper).
Tools: Mix the components in the double-syringe by means of the supplied mixing bowl and spatula.

APPLICATION

Mixture ratio: 1:1
Coverage: 1 ml = approx 1 cm² at a film thickness of 1 mm
Handling of packaging: Remove the spatula from the side of the double syringe, and the closure cap from the handle. Break the seal of the double syringe.
Directions for use: Press out an equal amount of both components onto the enclosed mixing tray. Mix these two equal parts well with a synthetic spatula until a mixture is obtained with a homogeneous colour. Apply the mixture, which at room temperature (+20°C) remains toolable for about 45 minutes, as a thin layer on one of the two materials. Join the materials and keep them in place for 10 hours. Be careful not to move the parts before the adhesive has cured. After use, clean the nozzle with a cloth and place the special cap in the handle on the double syringe. Resin and hardener must not come into contact with each other unless for usage.
Potlife: 45 minutes
Stains/Residue: Remove wet stains immediately with warm water and soap. Cured adhesive residue can only be removed mechanically.
Advice: Some types of synthetics can not be joined such as polyethylene and polypropylene. This can be tested by holding a glowing copper wire against the synthetics. Does it smell of wax? Then you can not bond it. Use a piece of adhesive tape in order to keep the parts in place while the adhesive is curing.
Points of attention: After use close well (note: always place back the cap in the same way, due to the bonding of the cap to the double syringe). For optimum performance it is important to create a larger amount of adhesive and mix it very well. Curing time depends on the temperature. Adhesive does not cure below +5°C.

 ___________________________________________________________

اطلاعات بیشتر و دستور استفاده برای نتیجه بهتر را میتوانید به صورت تلفنی یا زمان مراجعه دریافت نمایید.

مشهد، میدان ۱۵ خرداد، ضلع شمالی ( امام رضا ۵۰ )، پلاک ۲۰ ساختمان دنیای چسب
ساعت کاری : 8:30 الی 19 به صورت یکسره
تلفن : ۵۰ - ۴۰ - ۳۰ - ۳۸۱۱۲۲۲۰ - ۰۵۱