share
سنسور NCB10-30GM40-N0
  • سنسور NCB10-30GM40-N0
  • سنسور NCB10-30GM40-N0
  • سنسور NCB10-30GM40-N0

سنسور NCB10-30GM40-N0

سنسور نامور (NAMUR) مدل NCB10-30GM40-N0 از سنسورهای با تغذیه 8 ولت پپرل فوکس آلمان میباشد که قابلیت سنس تا 10 میلیمتر را داراست.ویژگی خاص سنسورهای نامور EX بودن یا کاربرد در مناطق انفجاری و خطرناک میباشد.از این سنسورها در مناطق HAZARDOUS AREA با گازها،بخار گازها و غبار گازها استفاده میگردد.قطر این سنسور نامور 30 میلیمتر است و دارای CATEGORY 1G; 2G; 3G; 1D; 3D میباشد.

قیمت

قیت همکار / عمده فروشی :

اطلاعات تامین کننده

عضو طلایی

هارمونیک کنترل نمایندگی PEPPERL+FUCHS ایران

تهران

وارد کننده، عمده فروش، خرده فروش، خدمات

نمایندگی PEPPERL+FUCHS، نمایندگی MTL، بریر پپرل فوکس، نمایندگی ACREL، بریر MTL، نمایندگی NOVUS، سنسور پپرل فوکس، بریر pepperl+fuchs، نماینده رسمی شرکت PEPPERL+FUCHS، سنسور pepperl+fuchs، نمایندگی IFM، رله PEPPERL+FUCHS، فروش بریر PEPPERL+FUCHS، فروش سنسور پپرل فوکس، نمایندگی پپرل فوکس، نمایندگی SICK

مشاهده سایت فروشنده

مشخصات

شرکت سازنده
PEPPERL+FUCHS
مدل
NCB10-30GM40-N0
کشور سازنده
آلمان
نوع خروجی
NAMUR NC
ولتاژ تغذیه
8 ولت
نوع اتصال
کابل2 متری از جنس PVC
جنس بدنه
Stainless steel 1.4305 / AISI 303
فرکانس سوییچینگ
200 هرتز
دمای کاری
40- تا 100 درجه سانتیگراد
قطر بدنه سنسور
30 میلیمتر
میزان سنس
10 میلیمتر
Category
1G; 2G; 3G; 1D; 3D
درجه حفاظتی
IP67

توضیحات محصول

Inductive sensor NCB10-30GM40-N0

  • 10 mm flush
  • Usable up to SIL 2 acc. to IEC 61508
  • Stainless steel housing
  • Datasheet excerpt: Technical data of NCB10-30GM40-N0
    General specifications
    Switching function Normally closed (NC)
    Output type NAMUR
    Rated operating distance 10 mm
    Installation flush
    Assured operating distance 0 ... 8.1 mm
    Actual operating distance 9 ... 11 mm typ.
    Reduction factor rAl 0.35
    Reduction factor rCu 0.3
    Reduction factor r304 0.75
    Nominal ratings
    Nominal voltage 8 V
    Switching frequency 0 ... 200 Hz
    Hysteresis 1 ... 15 typ. 5 %
    Reverse polarity protection reverse polarity protected
    Short-circuit protection yes
    Current consumption
    Measuring plate not detected min. 2.2 mA
    Measuring plate detected ≤ 1 mA
    Switching state indicator all direction LED, yellow
    Functional safety related parameters
    MTTFd 1870 a
    Mission Time (TM) 20 a
    Diagnostic Coverage (DC) 0 %
    Compliance with standards and directives
    Standard conformity
    NAMUR EN 60947-5-6:2000
    IEC 60947-5-6:1999
    Electromagnetic compatibility NE 21:2007
    Approvals and certificates
    FM approval
    Control drawing 116-0165
    UL approval cULus Listed, General Purpose
    CSA approval cCSAus Listed, General Purpose
    CCC approval CCC approval / marking not required for products rated ≤36 V
    Ambient conditions
    Ambient temperature -25 ... 100 °C (-13 ... 212 °F)
    Storage temperature -40 ... 100 °C (-40 ... 212 °F)
    Mechanical specifications
    Connection type cable PVC , 2 m
    Core cross-section 0.75 mm2
    Housing material Stainless steel 1.4305 / AISI 303
    Sensing face PBT
    Housing diameter 30 mm
    Degree of protection IP66 / IP67
    Cable
    Bending radius > 10 x cable diameter
    Equipment protection level Dc (tc)
    Instruction Manual electrical apparatus for hazardous areas
    Device category 3D for use in hazardous areas with combustible dust
    Certificate of Compliance PF 15CERT3774 X
    CE marking [*PD-Z02585A*]
    ATEX marking II 3D Ex tc IIIC T80°C Dc
    The Ex-related marking can also be printed on the enclosed label.
    Standards EN 60079-0:2012+A11:2013, EN 60079-31:2014
    Protection by enclosure "tc" Some of the information in this instruction manual is more specific than the information provided in the datasheet.
    General The corresponding datasheets, declarations of conformity, EC-type examination certificates, certifications, and control drawings, where applicable (see datasheets), form an integral part of this document. These documents can be found at www.pepperl-fuchs.com. The maximum surface temperature of the device was determined without a layer of dust on the apparatus. Some of the information in this instruction manual is more specific than the information provided in the datasheet.
    Installation, commissioning Laws and/or regulations and standards governing the use or intended usage goal must be observed. If the Ex-relevant identification is printed exclusively on the adhesive label provided, this label must be affixed in the immediate vicinity of the sensor! The background surface to which the adhesivelabel is to be applied must be clean and free from grease! The applied label must be durable and remain legible, with due consideration of the possibility of chemical corrosion!
    Maintenance No changes can be made to apparatus, which are operated in hazardous areas.
    Repairs to these apparatus are not possible.
    Special conditions
    Minimum series resistance RV A minimum series resistance RV is to be provided between the power supply voltage and the proximity switch in accordance with the following list. This can also be assured by using a switch amplifier.
    Maximum operating voltage UBmax The maximum permissible operating voltage UBmax must be restricted to the values given in the following list. Tolerances are not permitted.
    Maximum permissible ambient temperature TUmax Values can be obtained from the following list, depending on the max. operating voltage Ub max and the minimum series resistance Rv.
    at UBmax=9 V, RV=562 Ω 66 °C (150.8 °F)
    using an amplifier in accordance with EN 60947-5-6 66 °C (150.8 °F)
    Protection from mechanical danger The sensor must not be exposed to ANY FORM of mechanical danger.
    Protection from UV light The sensor and the connection cable must be protected from damaging UV-radiation. This can be achieved when the sensor is used in internal areas.
    Protection of the connection cable The connection cable must be prevented from being subjected to tension and torsional loading.
    Electrostatic charge Electrostatic charges must be avoided on the mechanical housing components. Dangerous electrostatic charges on the mechanical housing components can be avoided by incorporating these in the equipotential bonding. Avoid electrostatic charges that can cause electrostatic discharge when installing or operating the device. Information on electrostatic hazards can be found in the technical specification IEC/TS 60079-32-1. Do not attach the nameplate provided in areas where electrostatic charge can build up.
    General information
    Use in the hazardous area see instruction manuals
    Category 1G; 2G; 3G; 1D; 3D

لینک های مرتبط و فایل ها

سایر محصولات و خدمات شرکت