سنسور UC500-30GM-IUEP-IO-V15

Ultrasonic sensor UC500-30GM-IUEP-IO-V15

• IO-link interface for service and process data
• Programmable via DTM with PACTWARE
• Switch output and analog output
• Selectable sound lobe width
• Synchronization options
• Temperature compensation
• Datasheet excerpt: Technical data of UC500-30GM-IUEP-IO-V15

  Product Description
  Single head system

  General specifications
  Sensing range	30 ... 500 mm
  Adjustment range	50 ... 500 mm
  Dead band	0 ... 30 mm
  Standard target plate	100 mm x 100 mm
  Transducer frequency	approx. 380 kHz
  Response delay	minimum : 25 ms Ex works settings: 45 ms
  Indicators/operating means
  LED green	solid: Power on flashing: Standby mode or IO link communication
  LED yellow 1	solid: Object in evaluation range flashing: Learning function, object detected
  LED yellow 2	solid: Object in evaluation range flashing: Learning function, object detected
  LED red	solid red: Error red, flashing: program function, object not detected
  Electrical specifications
  Operating voltage	10 ... 30 V DC , ripple 10 %SS 15 ... 30 V voltage output
  No-load supply current	≤ 60 mA
  Power consumption	≤ 1 W
  Interface
  Interface type	IO-Link
  Protocol	IO-Link V1.0
  Transfer rate	Acyclical: typical 240 Bit/s
  Cycle time	min. 13.2 ms
  Process data witdh	16 bit
  Input/Output
  Input/output type	1 synchronization connection, bidirectional
  	0 Level	0 ... 1 V
  	1 Level	4 V ... UB
  	Input impedance	> 12 kΩ
  	Output rated operating current	< 12 mA
  	Pulse length	0.5 ... 300 ms (level 1)
  	Pulse interval	≥ 14 ms (level 0)
  Synchronization frequency
  	Common mode operation	≤ 70 Hz
  	Multiplex operation	≤ 90 Hz / n , n = number of sensors , n ≤ 10 (factory setting: n = 5 )
  Output
  Output type	1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected Current output 4 mA ... 20 mA or voltage output 0 V ... 10 V configurable
  Rated operating current	200 mA , short-circuit/overload protected
  Voltage drop	≤ 2.5 V
  Resolution	current output: evaluation range [mm]/3200 but ≥0.05 mm voltage output: evaluation range [mm]/4000 but ≥0.05 mm
  Deviation of the characteristic curve	≤ 0.2 % of full-scale value
  Repeat accuracy	≤ 0.1 % of full-scale value
  Switching frequency	≤ 11 Hz
  Range hysteresis	1 % of the adjusted operating range (default settings), programmable
  Load impedance	current output: ≤ 300 Ohm Voltage output: ≥ 1000 Ohm
  Temperature influence	≤ 1.5 % from full-scale value (with temperature compensation) ≤ 0.2 %/K (without temperature compensation)
  Approvals and certificates
  UL approval	cULus Listed, General Purpose
  CSA approval	cCSAus Listed, General Purpose
  CCC approval	CCC approval / marking not required for products rated ≤36 V
  Ambient conditions
  Ambient temperature	-25 ... 70 °C (-13 ... 158 °F)
  Storage temperature	-40 ... 85 °C (-40 ... 185 °F)
  Mechanical specifications
  Connection type	Connector M12 x 1 , 5-pin
  Degree of protection	IP67
  Material
  	Housing	Stainless steel 1.4305 / AISI 303 TPU Polyamides
  	Transducer	epoxy resin/hollow glass sphere mixture; polyurethane foam
  Mass	66 g